...

Air Freight Pallet Sizes: ULD Types, Dimensions and Weight Limits

An air freight pallet is an aluminum unit load device (ULD) for building cargo; the standard sizes are the 96 x 125 in PMC and 88 x 125 in PAG.

Your shipment arrives at the airline on ordinary wooden or plastic skids. The airline or its ground handler then builds those skids onto ULD pallets, nets them and loads them into the aircraft. Knowing the ULD sizes helps you plan skid footprints, heights and weights that fit cleanly, which keeps your air freight moving on the first available flight instead of waiting for a special position.

Key takeaways

  1. The two workhorse air cargo pallets are the PMC (96 x 125 in) and the PAG (88 x 125 in); both are used on main and lower decks of wide-body aircraft.
  2. Height, not base size, is usually the limit: about 64 in (163 cm) on a wide-body lower deck, and 96 in (244 cm) or 118 in (300 cm) on a freighter main deck.
  3. Maximum gross weight depends on the pallet certification and the aircraft position, so the lower of the two applies.

What a ULD pallet is and why it matters to shippers

A ULD is either an aircraft pallet with a net or an aircraft container. IATA treats ULDs as aircraft parts, because they lock into the floor and restrain the load in flight. Their design, testing and handling are governed by the IATA ULD Regulations, and each type carries a three-letter code: the first letter is the category (P for pallet), the second the base size, and the third the contour or other features.

For a shipper, three things follow. First, your freight is consolidated with other cargo on the same ULD unless you buy a whole pallet position. Second, the ULD base and contour set the outer limits of what can fly on a given aircraft. Third, freight that does not fit a standard build needs special handling, a freighter, or both, and that costs more. If you are weighing whether a full container-sized load can go by air, see our guide on whether you can air freight a container.

Standard air cargo pallet dimensions

The table lists the pallet types you will see most often on wide-body passenger aircraft and freighters. Base dimensions are standardized; maximum gross weights vary by manufacturer certification, so the figures below are common ratings and the operating airline’s limits always prevail.

IATA code (older code)Base, inchesBase, cmCommon max gross weightWhere it flies
PMC (P6P)96 x 125244 x 318Up to 6,804 kg (15,000 lb)Main deck and wide-body lower deck
PAG (P1P)88 x 125224 x 318Up to 6,804 kg (15,000 lb) on current certifications; some older units lowerMain deck and wide-body lower deck
PLA60.4 x 125153 x 318Up to 3,175 kg (7,000 lb)Wide-body lower deck, mostly side by side with containers
PRA (16 ft)96 x 196244 x 498About 11,300 kg (25,000 lb)Freighter main deck
PGA (20 ft)96 x 238.5244 x 606About 11,300 kg (25,000 lb), higher on some certificationsFreighter main deck

Two practical notes. The usable loading area is slightly smaller than the nominal base, because the edge profile and net fittings take a few centimeters on each side. And the tare weight of the pallet and net (around 120 kg for a PMC) is part of the gross weight, not part of your cargo allowance.

IATA estimates there are about 1 million ULDs in service worldwide, and its ULD safety program exists because damaged or badly built units are a flight safety risk. That is why a handler may refuse a skid that is broken, leaking or unstable: a bad skid can compromise the whole build.

Loose skids vs a full pallet position

Most shippers tender loose skids and pay by chargeable weight, with the airline or handler doing the build. Larger shippers and forwarders sometimes buy a whole ULD position and deliver a built-up unit (BUP) to the airline. A BUP rate can be lower per kilogram, but you pay for the full position whether you fill it or not, and the build must respect the airline’s contour and weight rules exactly. For one to four skids, loose cargo is almost always the right choice.

How your skids fit on a ULD base

A standard 48 x 40 in skid covers about 16% of a PMC base. Builders combine skids of different shippers to fill the base and the contour, so a skid that is unusually tall, overhanging or not stackable is harder to build and may wait for a better position. Square, stable, stackable freight with no overhang is the easiest to load on the next flight.

Contours and heights: main deck vs lower deck

The base is only half the story. Each aircraft position has a contour, the outline the built-up pallet must stay inside so it fits the fuselage curve and the cargo door. Common reference heights are:

  • Wide-body lower deck: about 64 in (162.6 cm), with angled upper corners to follow the hull. This is the height limit most shippers meet on passenger flights.
  • Freighter main deck, standard contour: about 96 in (243.8 cm).
  • Freighter main deck, high contour: about 118 in (299.7 cm), available only on certain positions of large freighters.
  • Narrow-body aircraft: most narrow-body lower holds take loose (bulk) cargo or small containers, not pallets, so palletized freight on these aircraft is limited.

These figures are typical published contours, not universal ones. Exact limits depend on aircraft type, position and the airline’s loading manual. For the detail on height planning, door sizes and how to split tall freight, read our guide to pallet height restrictions for air freight, and for overall piece limits see maximum dimensions for air freight.

A 65-inch skid is a freighter shipment

Freight that is even a few inches taller than the lower-deck contour cannot fly in the belly of a passenger jet. It moves to a freighter, which can mean fewer departures, a different routing and a higher rate. Measure your tallest skid, including the pallet base, before you book.

Weight limits: pallet, position and floor loading

Three separate limits apply, and the lowest one wins:

  1. Pallet certification. The maximum gross weight the ULD and its net are certified to carry, as in the table above.
  2. Aircraft position limit. The weight the aircraft structure allows at that position. Lower-deck positions often allow less than the pallet’s certified maximum.
  3. Floor loading. The weight per square foot the aircraft floor and the ULD base can take. A heavy machine on a small footprint may need a spreader, such as timber skids or a load-spreading base, to distribute the weight.

For a typical shipper of palletized goods, these limits rarely bind. They matter for dense items: metal parts, machinery, batteries, liquids in drums. Tell your forwarder the heaviest single piece and its footprint when you request a rate, not just the total weight.

How pallet size affects your air freight cost

Air freight is charged on chargeable weight, the greater of actual weight and volumetric weight. Tall, light freight eats contour space and is billed on its volume. A few planning habits reduce cost and delay:

  • Keep skid height under the lower-deck contour when possible, so the cargo can fly on passenger flights.
  • Avoid overhang. Cartons that extend past the skid edge add billable dimensions and get damaged during build-up.
  • Mark non-stackable freight clearly and expect to pay for the space above it.
  • Use consistent carton sizes so the pallet screens and builds quickly.

When you quote on ExFreight, enter the real dimensions and weight of each piece. Rates shown are instant, informational and subject to change; shipments can be re-invoiced if actual details differ, and inaccurate dimensions are the most common reason that happens.

Know your rate before you build the skidsEnter dimensions and weight to compare air options and transit times instantly.
Get a Free Quote

Frequently asked questions

What is the standard air freight pallet size?

The most common air freight pallets are the PMC, with a 96 x 125 inch base (244 x 318 cm), and the PAG, with an 88 x 125 inch base (224 x 318 cm). Both fly on wide-body passenger aircraft and freighters. Larger 16 ft and 20 ft pallets are used only on freighter main decks.

How tall can an air cargo pallet be?

On the lower deck of a wide-body passenger aircraft, the typical limit is about 64 inches (163 cm). Freighter main decks commonly take about 96 inches (244 cm), and some positions on large freighters allow about 118 inches (300 cm). The exact limit depends on aircraft type, position and the airline's loading manual.

How much weight can an air freight pallet hold?

A PMC or current PAG pallet is commonly certified up to 6,804 kg (15,000 lb) gross, and a PLA half pallet up to 3,175 kg (7,000 lb). The aircraft position and floor loading limits often allow less, especially on the lower deck. The lowest applicable limit always controls the build.

Can I ship standard 48 x 40 pallets by air?

Yes. Airlines accept standard 48 x 40 inch skids and build them onto ULD pallets, often together with other shippers' freight. Keep the skid stable, with no overhang, and below the lower-deck height limit if you want access to passenger flights. Chargeable weight still uses the full skid dimensions.

What is the difference between PMC and PAG pallets?

Both are 125 inches long. The PMC is 96 inches wide and the PAG is 88 inches wide, so the PMC offers more base area. Both fit main and lower decks of wide-body aircraft. The choice usually depends on the aircraft position and what the airline's ULD fleet carries.

Written by

ExFreight Team

ExFreight’s logistics experts with 15+ years of experience in freight forwarding from China to over 150 countries worldwide.

Published November 11, 2026
Tags

Table of Contents

Get a Free Quote

Smarter logistics start here.
Expert support for every shipment.

Related Articles

Scroll to Top
Seraphinite AcceleratorOptimized by Seraphinite Accelerator
Turns on site high speed to be attractive for people and search engines.